Please remove the insulation strip to activate the batteries. Ensure that the rubber seal is correctly placed to avoid water damage. To change from centigrade to fahrenheit please press the C/F button on the back of the thermometer (See Diagram C)

The Thermometer should now be ready for use and will pick up the room temperature and display it on the LCD.

To adjust the HOT bath water temperature alarm, press the “ON/SET” button and hold for 3 seconds, release and press “+” to change alarm temperature (See Diagram C). You can choose between 37, 38, 39 or 40°C. After the desired tempereture is set, just wait a few seconds and the temperature will be saved.

NOTE: The COOL temperature is set at 30°C and cannot be changed.

Place the thermometer in the baby’s bath and start to fill the bath with the required amount of water using cold water first. Once you have added the desired amount of cold water, slowly add hot water and stir until the temperature reached 37°C. This temperature is just right for your baby.

Your baby will feel most comfortable in the bath if the water temperature is between 37°C/98.6°F and 38°C/100.4°F. If the temperature is equal to or higher than the alarm temperature you set, the LED light above the display screen will flash red as a warning and the “Hot” symbol is displayed (See Diagram A). The screen will also display the actual temperature reading. If you see a reading of 39°C or higher DO NOT place your baby in the bath. Add cold water to bring the temperature down to 37°C/98.6°F. Over the duration of your baby’s bath time you should monitor the temperature regularly to make sure that the recommended temperature is maintained. If you notice the temperature drop below 30°C/86°F, the blue light will flash and the “Cool” symbol is displayed (See Diagram B). Add a little warm water making sure you do not pour hot water directly onto the baby. Once the bath time is over and the baby is warm, dry and safe, remove the thermometer from the water and towel dry. The thermometer screen will turn off automatically after 15 minutes.

The thermometer cannot measure the temperature outside the measuring range of 0-80°C. If the thermometer is subjected to temperatures outside of this range one of the messages in Diagram A or B will be displayed. 

Replacing the batteries

If the display becomes faded, the batteries need to be replaced for accurate results. To replace the batteries, use a screwdriver to unscrew the screw and open the cover. Replace the old batteries with new LR44 batteries. Observe the correct polarity. Do not mix old and new batteries. Please ensure that you place the rubber seal in the correct position and tighten the screw to keep the product waterproof. 

NOTE

•   Do not use different type batteries or new and used batteries together. 

•   Please observe the polarity when replacing the batteries.

•   The supply terminals are not to be short circuited.

•   When the batteries are fully exhausted, they must be removed from the product.

•   This product contains batteries. Please help to protect the environment. Do not    throw them away. Take them to a local civic waste collection point for recycling.

For use as a room thermometer

Place the thermometer on a surface or shelf that is out of direct sunlight and not near a heat/cooling source such as a radiator or air conditioner.

The temperature will be displayed in the digital display and will fluctuate as the   ambient temperature of the air fluctuates. The ideal temperature for a baby’s room is 18-20°C / 64.4-68°F. The thermometer will shut off automatically.

Cleaning and Maintenance

Wash the thermometer in soapy water, rinse and dry before using for the first time and after each use. Do not use abrasive or solvent based cleaning agents as this may cause damage to the product.

Not suitable for use in microwave, steam, or cold water sterilisers.

When not in use, store the thermometer in as dry area away from direct sunlight and heating/cooling sources.

Specification and notes

• Measuring range: 0°C-80°C / 32°F-176°F

• Accuracy: +/- 1°C

• Battery: 2xLR44 button batteries.

• ATTENTION

• For your child’s safety and health

•   NEVER LEAVE THE BABY UNATTENDED IN THE BATH.

•   ALWAYS CHECK THE TEMPERATURE OF THE WATER.

•   BEFORE PLACING THE BABY IN THE BATH.

•   Always use the product under adult supervision.

•   Before each use, inspect the product and stop using at the first sign of damage or weakness.

•   Keep all components not in use out of reach of children.

•   Whilst the readings given by the thermometer are accurate they should be used as a guide only.

•   Never open except to change batteries

•   The package has to be kept as it contains important information.

•   Keep the battery compartment lid and rubber seal out of reach of children.

•   After replacing batteries, the thermometer is only waterproof if the rubber seal is placed correctly.

•   The batteries should only be inserted/replaced by an adult.

•   Keep away from children when inserting/replacing batteries.

•   If a battery is swallowed, immediately see a doctor.

•   Use only LR44 type batteries. Others may cause damage.

•   Dispose of the product and batteries observing the rules and regulations in your country.

•   Non-rechargeable batteries are not to be recharged.